Mountain-off-road BBTJ0006 Bedienungsanleitung PDF herunterladen

MOUNTAIN OFF ROAD ENTERPRISES, LLC.

P.O. BOX 690 DELTA COLORADO 81416

970-625-0500

970-625-3747 FAX

E-mail: info@mountainoffroad.com

www.mountainoffroad.com

INSTALLATION INSTRUCTIONS for BBTJ0006 BombProof™ BLOCK BRACKETS

Please read and understand all instructions before beginning the installation of these motor mounts. Please read

the terms and policies on the back of these instructions.

The BBTJ0006 Block Brackets are designed to fit the following Jeep® vehicles: 2000-2006 TJ, LJ Wranglers

equipped with 6-cylinder engines (4.0L ). These Brackets will work with the OEM motor mounts along with most

Aftermarket Motor Mounts.

STEP 1: With the Jeep® on flat level ground, apply the parking brake, block the tires so it cannot move.

Put the transmission in neutral. Using a jack, place a block of wood between the jack and the oil pan. Apply a

slight amount of pressure on the oil pan. We recommend doing one side at a time.

STEP 2: On the drivers side remove the through bolt, lower nut and bolt on the motor mount and then

remove the motor mount. Save this hardware! remove the OEM block bracket and the bracket that attaches to

the block and to the AC compressor ( see figure 3 ). The new Block Bracket will reattach to the block using the

original three holes plus five additional threaded holes on the block. We recommend cleaning the new holes with

a 3/8”x16 tap. ( see figure 1)

STEP 3: Install the new DS Block Bracket and motor mount together, attach the block bracket using the

supplied hardware using loc-tite on the bolts, ( See Figure 2 for bolt locations). On the hole where the AC bracket

you removed in step 2 was, is where you will install the new supplied bracket, this bracket goes behind the block bracket ( see

figure 4 ). Do not tighten the bolts yet. Reinstall the original motor mount bolts and nuts and check to see if the

motor mount is in the same location as before, if not the block bracket can be moved slightly to realign the mount

to the frame bracket. After the alignment is correct tighten the block bracket bolts and the bolt and nut on the mo-

tor mount. Do not Tighten the through bolt on the motor mount at this time.

STEP 4: On the Passenger side Remove the through bolt, lower nut and bolt on the motor mount and

then remove the motor mount. Save this hardware! remove the OEM block bracket. The new Block Bracket will

reattach to the block using the original three holes plus five additional threaded holes on the block. We recom-

mend cleaning the new holes with a 3/8”x16 tap and the. ( see figure 3 )

Page 1

HARDWARE KIT:

1– DS Block Bracket

1– PS Block Bracket

11– 3/8-16x1 Bolt

4– 3/8-16x1-1/4 Bolt

1– 3/8-16x1-1/2 Bolt

16– 3/8” Flat Washers

16– 3/8” Lock Washers

1– AC Bracket

1 2 3

Inhaltsverzeichnis

Seite 1 - 970-625-0500

MOUNTAIN OFF ROAD ENTERPRISES, LLC. P.O. BOX 690 DELTA COLORADO 81416 970-625-0500 970-625-3747 FAX E-mail: [email protected] www.moun

Seite 2 - DS Block Bracket Installed

STEP 5: Install the new PS Block Bracket and the Motor mount together, attach the block bracket using the supplied hardware using loc-

Seite 3 - PS Block Bracket Installed

TERMS-POLICIES: FIT and TOLERANCES: These Motor Mounts are the results of countless hours of research, testing, fitting and refining.

Kommentare zu diesen Handbüchern

Keine Kommentare

Mountain-off-road BBTJ0006 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Mountain-off-road BBTJ0006 herunter. Mountain Off Road BBTJ0006 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Mountain-off-road BBTJ0006